86-373-3510262
Torch Park, High-Tech Zone, No. 1789, Xinfei Road, Xinxiang, Henan, China (Mainland)
to get 95C Boiling Water 480ml/minute
Product Description
Thick film heater has become a new type of heater.
The thick film heater uses new techniques and mature technology, and it is the best substitute for traditional heaters.
The prospect of application in the field of thick film heater is very wide because of its advantages such as high speedy heating. These products not only economize on much energy, but also use unpolluted energy. It doesn’t pollute the environment, and the used products can be recycled, so thick film heater has become a heater that can protect the environment, and save the energy.
Installation and Use
As this is a new type tubular structure water flow instant heating element, it can connect with water route directly.
SUS444 Thread Connector can be welded on the heater tube.
In order to mount it easily, we assemble plastic housing, PP end caps, thermostats (prevent dry heating), NTC sensor, wire leads. It can be mounted by side or two ends.
Product Characteristics
Compared with other immersion water heater elements, Jieda Thick FIlm Heating Tube/Element are advanced in bigger heat area, higher power density, faster temperature ramp up (80℃/S). This heating assembly useφ30mm thick film stainless steel heating tube. Power: 2200W/3000W.Temperature control function is available if it matched with circuit board.Its working life is above 10000 hours.
Φ30mm*110mm(length) | Heat Density | >40W/cm² | |
Ramp-Up Rate | 150℃/s | Thermal Efficiency | >96% |
Heating Power | 2200W | Service Life | >10,000 hours |
Rated Voltage | 220v | Certificate | CQC, RoHS |
Dielectric Strength | 1,500V/5mA/60s | Power Deviation | -10% - +5% |
Leakage Current | ≤0.25mA | Insulation Resistance | ≥200MΩ |
Type | Thick Film Water Flow Instant Water Heating Tube | Application | to replace iron immersion electric water heating element |
Shield Thermistor | PTC | Grounding Type | Spot-Weld |
Product Application
JD30 is widely applied in water purifier, water dispenser, pipeline water dispenser, electric faucet and other type of home appliances.
Related Products
Available Thick Film Heating Tube Element diameter are 18mm, 20mm, 30mm, 35mm, 40mm and 50mm
Power watts are 2.2kw, 3kw, 3.5kw, 3.8kw, 4kw, 5.5kw and 6kw
Mainly applied in Water Flow Instant Heating. Due to its long life time and higher thermal transfer, it's ideal to replace traditional immersion water heating elements.
FAQ
Q: What's Thick Film Heating Element?
A: -Thick Film Heater is a new technical art which is use screen printing technology and new thick film material.
It is printed with isolation dielectric, heating element and glass prevent on a substrate that is made by stainless steel, and through drying firing process with 800°C. Thick Film Heater has become a new type of heater.
Q: What’s the advantages of Jieda Thick Film Heating Element?
A: We fully master screen printing and sintering technology on curved surface stainless steel tubes, which makes it possible to heat continuous water flow without water tank.
60W/CM² POWER DENSITY
UP TO 150℃/S TEMPERATURE RANP UP
Q: What's the inlet and outlet diameter?
A: Thick Film Heating Tube : Ø18, Ø20, Ø30, Ø35, Ø40, Ø50mm
Thick Film Heating Element : Available with Ø10mm, Ø16mm and G1/2 OD20.9mm
Q: How to get the suitable model for our application?
A: We need to know the water temperature in inlet and outlet port, water flow rate, connection port details and other special requirements, to recommend the suitable Thick Film Heating Elements.
Q: What's the operation attentions?
A: 1. The temperature ramp-up above 80°C/s, please make sure the tube fulfilled with water before use.
2. Please install it vertically, make sure water flow direction from bottom to top, to prevent DRY HEATING in partial area of heating tube.
3. Set the minimum flow rate according to tubes' power watts, ensure smooth flowing of water, to prevent vaporizing and dry heating
4. Make sure reliability grounding.
about Us
